Figure 5. The curves above show the effect of the 'treble tilt', 'bassFigure 6. The upper curve group shows the horizontal directivity
tilt' and 'bass roll-off' controls on the free field response.characteristics of the 1030A measured at 1m. The lower curve is the
1/3 octave band power response.
SYSTEMSYSTEMSYSTEMSYSTEMSYSTEMAMPLIFIERAMPLIFIERAMPLIFIERAMPLIFIERAMPLIFIERCROSSOVERCROSSOVERCROSSOVERCROSSOVERCROSSOVER
SPECIFICATIONSSPECIFICATIONSSPECIFICATIONSSPECIFICATIONSSPECIFICATIONSSECTIONSECTIONSECTIONSECTIONSECTIONSECTIONSECTIONSECTIONSECTIONSECTION
Lower cut-off frequency, -3 dB: < 52 HzBass amplifier output power with a 4 OhmInput connector: XLR female pin 1 gnd
Upper cut-off frequency, -3 dB: > 20 kHzload:pin 2 +
Short term80 Wpin 3 -
Free field frequency response of system:
55 Hz - 18 kHz (? 2.5 dB)Treble amplifier output power with anInput impedance: 10 kOhm balanced
8 Ohm load:
Maximum short term sine wave acousticShort term50 WInput level for 100 dB SPL output @ 1m:
output on axis in half space, averaged fromvariable from +6 to -6 dBu
100 Hz to 3 kHz:Long term output power is limited by
@ 1m> 105 dB SPLdriver unit protection circuitry.Input level for maximum short term sine
@ 0.5m > 111 dB SPLwave output of 105 dB SPL @ 1m:
variable from +11 to -1 dBu
Maximum long term RMS acoustic output inAmplifier system distortion at
same conditions with IEC weighted noisenominal output:Subsonic filter below 50 Hz :
(limited by driver unit protection circuit):THD< 0.08%18 dB/octave
@ 1m> 99 dB SPLSMPTE-IM< 0.08%
@ 0.5m > 105 dB SPLCCIF-IM< 0.08%Ultrasonic filter above 25 kHz:
DIM 100< 0.08%12 dB/octave
Maximum peak acoustic output per pair on
top of console, @ 1 m from the engineerSignal to Noise ratio, referred to fullCrossover frequency, Bass/Treble: 3.5 kHz
with music material:> 115 dBoutput:
Bass> 95 dBCrossover acoustical slopes:
Self generated noise level inTreble> 95 dB24 - 32 dB/octave
free field @ 1m on axis:< 10 dB
(A-weighted)Mains voltage:100/200 or 115/230 VTreble tilt control operating range in 2 dB
Harmonic distortion at 90 dB SPL @ 1m onVoltage operating range:?10%steps:from +2 to -4 dB &MUTE
axis:
Freq: 60...150 Hz< 3%Power consumption:Bass roll-off control operating range in 2 dB
> 150 Hz< 0.5%Idle20 VAsteps:from 0 to -8 dB @ 50 Hz
Full output100 VA
Drivers: Bass 170 mm (6 1/") coneBass tilt control operating range in 2 dB
2
3
Treble 19 mm (/4") metalsteps:from 0 to -6 dB @ 100 Hz
dome& MUTE
Both drivers are magnetically shielded.
The 'CAL' position is with all tone controls
Weight:7,6 kg (17 lb)set to 'off' and the input sensitivity control to
Dimensions:maximum (fully clockwise).
1
Height 312 mm (12 /4")
7
Width 200 mm ( 7 /")
8
Depth 240 mm (9 7/")
16
Note! All frequency response curves were measured in
a calibrated, 12 m cube, anechoic chamber at 1 m
using grade 1 measuring equipment. Input signal levels
were set at -20 dBu. The anechoic chamber error in the
Genelec Oy, Olvitie 5Genelec Inc, 7 Tech Circle
free field response is less than 0.5 dB down to 60 Hz.
FIN - 74100 IISALMI, FINLANDNatick, MA 01760, USA
Phone:+358 - 17 - 83 881Phone:+1 -508/652-0900
Fax:+358 - 17 - 812 267Fax:+1 -508/652-0909
Data Sheet No. DR30001
E-mail:
[email protected]:
[email protected]
COPYRIGHT GENELEC OY 6/1999
Web:http://www.genelec.com
All data subject to change without prior notice
ACEC
